Technician A says that some people refer to the blower motor fan
as a squirrel fan. Technician B says that changing the blower fan
speed can be done by using a solenoid. Who is correct?
Tech A
Tech B
Both Techs A and B
ONeither Tech A nor B

To get the heat loss of an entire building, you divide the building into areas that have the same U value, and then add them all up to get the total heat loss.

Q=U*A*T, or more simply put, the heat loss of an area of size A is determined by the U value of the materials and the temperature difference between inside and outside (i.e., the temperature difference between the two surfaces, not the two air temperatures).

You must divide a building into sections with the same U value in order to calculate the overall heat loss for the entire structure.

Thermal conductivity is the ability of an object to transfer thermal energy into another object when it comes into touch with one that is at a lower temperature. A cylinder's energy transfer rate while its contents are at high temperatures

To learn more about  heat loss refer to:

https://brainly.com/question/18329426

#SPJ4

Refer to the attached images. Final answer is circled.

In order to determine absolute pressure, a complete vacuum is used. While the average atmospheric surface pressure is approximately 14.7 PSIA.

The pressure in a vessel absolutely devoid of any air molecules would be 0 PSIA. PSIA stands for absolute pounds per square inch. Absolute pressure is the pressure exerted with relation to absolute zero or vacuum. Engineering documents or P&IDs might employ PSIA. Pounds per square inch gauge is referred to as PSIG. PSIA is a word used to describe absolute pressure in PSI, which includes atmospheric pressure. "Total pressure" is another name for absolute pressure. We add 14.7 PSI since this atmospheric pressure is comparable to 14.7 PSI at sea level. Higher heights have lower atmospheric.

Learn more about engineering here-

https://brainly.com/question/27162243

#SPJ4

The  numerical values  of a2 = 0.002*a1 / 16

The magnitudes of the frequency component at 800 Hz and at

1600 Hz are: 4²a2cos²(800nt) and  8²a2cos²(800nt)cos²(1000nt)

a) To evaluate the numerical values of a1 and a2, we can use the test data given. The measured frequency component at 1000 Hz is 1V, so we can set that as the value of a1cos(1000nt) in the amplifier output equation:

Uo(t) = a1cos(1000nt) + a2[4cos(800nt) + cos(1000nt)]²

The ratio of the frequency components at 500 Hz to that at 1000 Hz is 0.002, so we can use that to find the value of a2:

Uo(t) = a1cos(1000nt) + a2[4cos(800nt) + cos(1000nt)]²

= a1cos(1000nt) + a2[16cos²(800nt) + 8cos(800nt)cos(1000nt) + cos²(1000nt)]

= a1cos(1000nt) + a2(16cos²(800nt) + 8cos(800nt)cos(1000nt) + cos²(1000nt))

The frequency component at 500 Hz is the second harmonic of the 800 Hz component and is given by 16cos²(800nt), so we can compare it to the 1000 Hz component:

16cos²(800nt) = 0.002 * a1cos(1000nt)

a2 = 0.002*a1 / 16

b) Since the input to the amplifier is a sum of cosine functions with different frequencies, the output will also be a sum of cosine functions with the same frequencies, but with different amplitudes.

The 800 Hz component in the input is 4cos(800nt) and is squared in the output equation, so the 800 Hz component in the output will be 4^2a2cos^2(800nt) which is a smaller amplitude than the 800 Hz component in the input.

The 1600 Hz component in the input is created by the product of the 800 Hz component and the 1000 Hz component, which is 8cos(800nt)cos(1000nt) and is squared in the output equation. so the 1600 Hz component in the output will be 8^2a2cos^2(800nt)cos^2(1000nt) which is even smaller than the 800 Hz component in the input.

Learn more about audio amplifier from

https://brainly.com/question/15610180
#SPJ1

Answer:

ur hhbkiegtbckdj you and your family a very merry merry

The species are arranged in such planar manner. neither antiaromatic nor aromatic

species definition

A species is a unit of biodiversity as well as the fundamental categorization and taxonomic rank of an organism in biology. The biggest collection of creatures in which any two persons of the right sexes or mating types may conceive a fertile child, typically by sexual reproduction, is referred to as a species. A species can also be identified by its karyotype, DNA sequence, anatomy, behaviour, or ecological habitat. In addition, since fossil reproduction cannot be studied, palaeontologists employ the chronospecies idea. There are approx 8 and 8.7 million different species of eukaryotes, based on the most current accurate estimate.

To know more about species
https://brainly.com/question/13259455
#SPJ4

The point coordinates for all atoms that are associated with the FCC unit  cell, i.e. fig b are:

bottom face: (1,0,0) (1,1,0) (0,1,0) (1/2,1/2,0)

Tope face: (0,0,1) (1,0,1) (1,1,1) (0,0,1) (1/2,1/2,1)

front and back face: (1/2,1,1/2) (1/2,0,1/2)

Left and Right face: (0,1/2,1/2) (1,1/2,1/2)

Atoms are found in an FCC unit cell at the centre of each cube's face and at each of the crystal lattice's four corners. Only half of each atom, which is located at the face centre, belongs to one particular cell and is shared by two adjacent unit cells.

A crystal lattice in an FCC unit cell contains atoms in each corner. Additionally, every cube face has an atom in the centre of it. Two next-to-one another unit cells share this face-center atom. A unit cell only contains 12 of each atom.

Learn more about FCC unit cell

https://brainly.com/question/12977980

#SPJ4

The force that this liquid ultimately exerts on plate B is therefore: F = 1000 kg/m3 9.8 m/s2 0.5 m2 2 m = 98 N

A push is an effect that can alter an object's motion according to physics. A force may cause an object with mass to accelerate when it changes its velocity, for as when it drifts away from rest. A known way to describe force is as a push or a pull. A vector quantity, it has both direction and magnitude. It is computed using the newton SI unit (N). Force is represented by the letter F. (formerly P).

Forces are always strong and have a purpose. As seen in the video whenever Zoe softly strikes the golf ball, forces can be mild. Or even a force can indeed be strong, as in the case of Izzy's powerful strike on the ball. Forces have a direction as well.

To know more about force visit :

brainly.com/question/13191643

#SPJ4

Vo and Io in the circuit is v^0=32V And I^0=0.8 A

Step by step explanation:

Given circuit:
Resultant equivalent resistance is                                        
R^ e q=(700||30)+(20||5)
=21+4
R^ e q=25
Total current=v/R^ e q
I=200/25
I=8A

Therefore ,Apply nodal analysis at v^ 1
v^ 0=v^1
200-V0/70+ 200-v^ 0/30=8
6000-30v^0+14000-70v^0/2100=8
20000-100v^0/2100=8
=20000-100v^0=16800
=100v^0=3200
v^0=3200/100
v^0=32V            

Apply nodal at V^ 2.
I^0=V^0-200/30+v^0/5
I^0=32-200/30+32/5
I^0=-168/30+32/5
I^0=-5.6+6.4
I^0=0.8 A


What Does Equivalent Resistance Mean?

An equivalent resistance is defined in physics as the sum of the resistances of the resistors connected in a circuit. Resistors can be wired in series or parallel. Assume that the three resistors are R1, R2, and R3.

If you connect these three resistors in series, the equivalent resistance is given by

Re = R1 + R2 + R3        

To learn more about Vo and Io in the circuit
https://brainly.com/question/13889633          
#SPJ4

Environmental Impact Assessment (EIA) is often required for significant development projects such as road construction, building construction, and industrial facility construction in order to analyze and minimize any environmental repercussions.

It is to be noted that the process of determining how a project or activity will affect the environment is known as environmental impact assessment.

It assists individuals in ensuring that the project will not hurt animals, plants, or natural resources. This manner, we can be sure that the things we construct or do won't affect the world.

Learn more about Environmental Impact Assessment:
https://brainly.com/question/30120335
#SPJ1

(a) The acceleration of block A is 10 ft/s^2.
(b) The velocity of block A after it has moved through 10 ft is 20 ft/s.
(c) The time required for block A to reach a velocity of 20 ft/s is 2 seconds.

How does acceleration work?

The rate at which an object's velocity with respect to time changes is referred to as accelerating in mechanics. It is a vector quantity to speed (in that they have magnitude and direction). The direction of the net force applied on an item determines the direction of its acceleration. According to Newton's Second Law, the amount of an organism's acceleration is the cumulative result of two causes:

(1) That item's mass, based on the materials from of which it is formed, — size is inversely related to the object's mass. (2) The net balance of all external forces acting against that object — magnitude is directly related to this net resultant force.

To know more about acceleration
https://brainly.com/question/12550364
#SPJ4

When examining a force's geometric representation or its algebraic equivalent, the components of a force can be viewed as horizontal and vertical changes.

The vertical and horizontal forces that combine to create the resulting force are represented by a force's components. A force can be broken down into two parts that are either inclined or perpendicular to one another. Two components are referred to as rectangular components when they are perpendicular to one another and as inclined components when they are inclined toward one another. Force has two parts: magnitude and direction. When examining a force's geometric representation or its algebraic equivalent, the components of a force can be viewed as horizontal and vertical changes.

Learn more about magnitude here-

https://brainly.com/question/13686176

#SPJ4

The acceleration of block A is 8.4949 and block B is 4.2475 ft/s² while the tension is the cable is 121.168 lb.

When there are two forces acting on the ends of a cable, rope, wire, or string, it is said to be under tension. The cable has a one-direction pull along its entire length, pulling equally in both directions on objects at either end.

Tension can also be used to describe the forces that are acting on both ends of the two elements. In other words, tension's polar opposite is compression.

Physical objects must exert some force on one another in order to make contact with one another. Depending on the kind of object, each of these contact forces will be unique.

Take a section about the rope near block B and using the show datum

SB + (SB - SA) = l

2SB  - SA = l

2SB  - SA = 0

2aB - aA = 0

aA = 2aB

Take FBD of block-A

(Upward+) ∑Fₓ = mAaA

T - W[tex]_A[/tex]sin20° = mAaA

T - 200sin20° = (W[tex]_A[/tex]/g)(2aB)

T = 200sin20° + (W[tex]_A[/tex]/g)(2aB)

Take FBD of block-B;

(Downward+) ∑Fₓ = mBaB

W[tex]_B[/tex]cos20° - 2T = mAaA

300cos20° - 2(200sin20° + (W[tex]_A[/tex]/g)(2aB)) = (W[tex]_B[/tex]/g)(a[tex]_B[/tex])

300cos20° - 2(200sin20° + (200/32.2)(2aB)) = (300/32.2)(a[tex]_B[/tex])

a[tex]_B[/tex] = 4.2475 ft/s²

Acceleration of A is given as;

⇒ aA = 2aB

⇒ aA = 8.4949 ft/s²

Tension is given as;

T = 200sin20° + (200/32.2)(2(4.2475))

T = 121.168 lb

Thus, the acceleration of block A is 8.4949 and block B is 4.2475 ft/s² while the tension is the cable is 121.168 lb.

Learn more about tension

https://brainly.com/question/11348644

#SPJ4

Using APA reference style, the references is attached below from Feldman, R. S. (2013) to American Psychology Association (2020)

APA reference style is a style of citing sources used by the American Psychological Association. It is primarily used in the social sciences and includes guidelines for citing sources both within the text of a document and in the reference list at the end of the document. The guidelines provide a consistent way of citing sources to make it easier for readers to identify and locate the sources cited in a document.

In the given problem, if we need to write the reference using APA style, it will take this format below

Reference Page:

Feldman, R. S. (2013). Psychology and your life (2nd ed.). New York, NY: McGraw Hill Companies.

Frontline. (n.d.). League of denial. Retrieved from https://www.pbs.org/wgbh/frontline/film/league-of-denial/

Friends. (2004). The one after Joey and Rachel kiss [Television series episode]. In D. Crane, & M. Kauffman (Executive producers), Friends. Burbank, CA: Warner Bros. Television.

Silver Linings Playbook. (2012). [Motion Picture]. United States: The Weinstein Company.

U.S. Energy Information Administration. (2013). Annual energy outlook 2013 with projections to 2040. Retrieved from http://www.eia.gov/forecasts/aeo/er/pdf/0383er(2013).pdf

Snickers. (2013, April 2). You’re not you when you’re hungry [Video file]. Retrieved from https://youtu.be/2rF_FRCd_LA

American Psychological Association. (2020). Publication manual of the American Psychological Association (7th ed.). doi:10.1037/0000165-000

Learn more on APA reference style here;

https://brainly.com/question/28008158

#SPJ1

CPU SS: A two-core superscalar processor with two function units that can handle out-of-order issues (FUs). On each core, only one thread can be active at once. CPU MT.

a fine-grained multithreaded processor that enables simultaneous execution of instructions from two threads (i.e., there are two functional units), but only one thread's worth of instructions can be issued at a time. CPU SMT: A SMT processor that has two functional units and supports running instructions from two threads simultaneously. Instructions from either or both threads may be sent to execute on any cycle. A high-level, all-purpose programming language is the C language. It offers a simple, reliable, and effective interface for system programming.

Learn more about function here-

https://brainly.com/question/17216645

#SPJ4

Answer:C

Explanation:

Note that possessing an ASE Certification is crucial because; " Leads to better employment opportunities." (Option D)

ASE certification, commonly known as Automobile Service Excellence, is given to an automotive mechanic who has finished the necessary training and acquired their Automotive Service Excellence Certified Master Technicians criteria.

There are 58 ASE certification examinations available, covering nearly every facet of the automobile repair and service sector.

The National Institute for Automotive Service Excellence (ASE) offers four levels of certification. They are:

Learn more about ASE Certification:
https://brainly.com/question/28436848
#SPJ1

According to the question, the largest permissible bending moment is 1382.5 KN m.

What is bending moment?
Bending moment is a mechanical force that causes a bending or flexing effect on a structural element such as a beam, resulting in the creation of a moment or torque about the element's neutral axis. It is calculated based on the internal forces acting on the element, such as the weight of the beam and the force of the load applied to it. Bending moment can be positive or negative, depending on the direction of the force and the location of the neutral axis.

M = (h×A×E×σ_allowable)/6

M = ((9mm×30mm×70GPa×100MPa)+(9mm×30mm×105GPa×160MPa))/6

M = 1382.5 KN m

To learn more about bending moment
https://brainly.com/question/13390572

#SPJ4

This can be achieved through a variety of programming languages, here's an example using Python:

A = 4

B = 5

C = 6

if A == 5 or B == 5 or C == 5:

   print("TRUE")

else:

   print("FALSE")

A formal language with many instructions is referred to as a programming language. These guidelines are presented to find different outputs. Computer programs are the main use of programming languages. A set of guidelines are presented to ensure the computer's proper operation.

Programming languages are used to control the external devices. In this example, the code checks if any of the variables A, B, or C is equal to 5. If any of them are, the code will output "TRUE", otherwise it will output "FALSE".

Learn more about programming on:

https://brainly.com/question/16936315

#SPJ1

The spreadsheet listing the pairwise distances in miles between the top 100 US cities by population may be found in the attached Distances.xlsx file.

Below is a screenshot of the spreadsheet. The city names are formatted as follows in the first row and first column: Nashville, TN is an example of a city name, comma, and capitalized state abbreviation. Keep in mind that the spreadsheet's first cell, A1, is empty. Create the get distance function, which takes two character vector inputs representing the names of two cities, as its only parameter. As an output argument called distance, the function returns the separation in between them. Get distance("Seattle, WA","Miami, FL"), for instance, should return 3723. The function returns -1 if one or both of the provided cities are not found in the file.

Learn more about function here-

https://brainly.com/question/17216645

#SPJ4

For a kid weighing 50 kg, does she hold her legs up when she swings down from rest at? 1 = 30° and Ф2 = 27°

Fint prior to = 0 T1 9V1 = T2 + V2 0 + 2.8 (1-cos30) (50) 9.81 = 1/2 (50) (50) V12 plus 0 V1 equals 2.713 m/sec

H1 = H2 \s50(2.713)(2.8) = 50 V2 (3) (3)

V2 = 2.532 =2.53 m/sec immediately following = 0, T2 +V2 = T2, V3 1/2 850(2.532)2, and 50(9/81)(3). (1-cos02)

27 degree is equal to 0.1089 = 1-cos02 2.

Children grow and develop in certain ways. They must be able to sit up on their own, for instance, before they can swings and subsequently walk. The same is true for how they master penmanship. Before the child can write, they tear, cut, and scribble on things. Before kids can hold a pencil and form readable symbols, called letters, in their hands, they must first develop the tiny muscles (fine motor muscles).

Learn more about Swing here:

https://brainly.com/question/1230851

#SPJ4

Note that the Bernoulli equation cannot be applied when the flow is "Rotational" (Option 1)

Bernoulli's equation formula represents a relationship between a fluid's pressure, kinetic energy, and gravitational potential energy in a container.

The Bernoulli equation assumes that the fluid flow is irrotational, meaning there is no net fluid flow around a closed loop. Rotational flow, also known as turbulent flow, is characterized by eddies and vortices and cannot be described using the Bernoulli equation.

Learn more about the Bernoulli equation:
https://brainly.com/question/6047214
#SPJ1

K=2*L-1 is the relationship between the number of nodes (K) and leaves (L). Therefore, L and k do not always have a stable relationship.

Number of internal nodes for L leaves = L - 1

So total nodes = 2L – 1

The following relation applies for a k-ary tree where each node has k offspring or none at all: L = (k-1)*n + 1.

where n represents the number of internal nodes and L represents the number of leaf nodes.

Every internal node will have K children since the k tree is fully developed.

A pointer to the topmost node of the tree, sometimes referred to as the "root," serves as the representation of a binary tree. The root's value is NULL if the tree is empty. The following components are present in each node of a binary tree:

Pointer to left kid in data

to the right-hand kid

Basic Binary Tree Operation:

adding a new element.

Learn more about Nodes here:

brainly.com/question/24068343

#SPJ4

According to the figure, G1 is represented by parts 4, 5, and 6 numbered part(s) of the cycle.

What is numbered part?
Numbered parts are individual parts of a larger item that are identified by a unique numerical identifier. This number can be used to easily locate and identify the part within the larger item. Numbered parts are often used in complex systems, such as machines, tools, vehicles, and buildings, where multiple components must be located and identified quickly and accurately. For example, a car engine may have hundreds of different numbered parts, each with its own unique identifier. Numbered parts also make it easier for manufacturers to track and inventory the parts used in their products. This helps them to ensure that the right parts are in place and available when they are needed.

To learn more about numbered part
https://brainly.com/question/11250014

#SPJ4

Volume fraction=1.175.        

Explanation:

Given:
Weight of empty crucible=47. 6504 g.
Weight of crucible and piece of composite= 50. 1817 g
Weight of crucible and glass after  burn-off = 49. 4476 g
weight and volume fraction of glass fiber and
epoxy resin=  w glass/w resin

w resin=50. 1817 g- 49. 4476 g = 0.7341 g
w glass=49. 4476 g-47. 6504 g = 1.7972 g

w fraction=1.7972 g/0.7341 g=2.448

                     
Now,
volume of glass fiber=1.7972 g/2.5g/cm^ 3
=0.7188 cm^ 3

volume of epoxy resin=0.7341 g/1.29/cm^ 3
=0.61175 cm^ 3

Volume fraction=v glass/v epoxy resin=0.7188/0.61175cm^ 3
Volume fraction=1.175.            

The volume fraction (percentage by volume) is one way to express the composition of a mixture with a dimensionless quantity; others are the mass fraction (percentage by weight) and mole fraction (percentage by moles)                    

To learn more about  volume fraction
https://brainly.com/question/23477586
#SPJ4    

An engineer would indicate the unit of measurement used in a design in millimeters.

The primary unit of measurement is the stocking unit of measure for a given item in a specific organization. You must define an item attribute that serves as the primary unit of measurement when creating each item.

Because the technical drawings are scaled, engineers, architects, and builders may create the items according to exact specifications.

When understanding scales, the number on the left relates to the measurement of the drawing, while the number on the right represents the actual size of the object.

Therefore, a millimeter is used in a design.

To learn more about measurements, refer to the link:

https://brainly.com/question/28390923

#SPJ1

The engineer observed that the tunnel was 460 feet long 26 days after the tbm was introduced. Therefore, the tunnel was completed 460 feet - 140 feet = 320 feet after the tbm was introduced.

What is tunnel?
A tunnel is an underground or underwater passageway, typically constructed for transportation purposes. Tunnels are typically used to bypass obstacles such as mountains, rivers, or bodies of water, or to provide a secure route for transportation of goods and people. Tunnels may also be used for mining, research, or military purposes. Tunnels can be constructed using a variety of materials, including steel, reinforced concrete, rock, earth and soil. The length of a tunnel varies from a few metres to several kilometres. When constructing a tunnel, safety is of paramount importance. Special engineering techniques are used to ensure the stability of the tunnel and its construction is closely monitored and regulated. Tunnels are designed to be resistant to weather, vibration, fire, and other environmental factors.

To learn more about tunnel
https://brainly.com/question/29050301

#SPJ4

It is true that following client instructions is essential for a flawless delivery. We need 8–15 seconds for eye-lead to use REPS and Checks to remove distractions.

For the first query, "Delivery," the topic is how to satisfy clients by delivering what they have requested. Therefore, by according to the customer's instructions, we can accomplish a flawless delivery.

For the second question, REPS and check means identifying the risks, removing them, making plans, and looking for space. It also means checking for yourself, the risks, the space, and the speed.

To prevent accidents while driving, the REPS and check procedure is employed as a safety measurement. The eye-lead varies depending on the route followed, but it typically lasts between 8 and 15 seconds.

Learn more about REPS here:

https://brainly.com/question/29749274

#SPJ4

The amount of gain that can be raised or lowered without causing the system to become unstable is referred to as the gain margin.

Learn more about Bode plot refer to :

https://brainly.com/question/28029188

#SPJ1