What force causes a resistance in motion
when two surfaces are touching?

Answers

Answer 1

Answer:

FRICTION

Explanation:

Friction is a force, the resistance of motion when one object rubs against another.

Answer 2

Frictional force

Explanation:

Its the opposing force against horizontal motion


Related Questions

Problem 4.13: Sound waves travel through air at a speed of 330 m/s. A whistle blast at a frequency of about 1.0 kHz lasts for 2.0 s. (a) Over what distance in space does the "wave train" representing the sound extend? (b) What is the wavelength of the sound? (c) Estimate the precision with which an observer could measure the wavelength. (d) Estimate the precision with which an observer could measure the frequency.

Answers

Answer:

a)  x = 660 m, b)  λ = 0.330 m, c) Δλ = 0.1 cm, d)    Δf = 104

Explanation:

a) the distance in which the train of waves extends can be obtained from the uniform movement

             v = x / t

             x = v t

             x = 330 2

             x = 660 m

b) the speed of sound is related to the wavelength and frequency

             v = λ f

              λ = v / f

              λ = 330/1000

              λ = 0.330 m

c) The precision in the measurement of the wavelength refers to the error or uncertainty in the measurement, if the measurement is direct with a tape measure the precision is the appreciation of the tape measure, in general it is 0.1 cm

d) the accuracy of the frequency in general the frequency is calculated from the measurements of period T

                f = 1 / T

The precision of the period is data by the chronometer used, in general time a press of 0.01s, by the response time of the people

               Δf = df / dT    ΔT

               Δf = 1 / T² ΔT

                Δf = 1 / (0.001)² 0.01

                 Δf = 104

As we can see, a much more precise system is needed to reduce the error

An insulated, vertical piston-cylinder assembly contains 50 L of steam at 105 oC. The outside pressure is 101 kPa. The piston has a diameter of 20 cm and the combined mass of the piston and the load is 75 kg. The electrical heater and the paddle wheel are turned on and the piston rises slowly by 25 cm with a constant pressure. The total internal energy increases by 3.109 kJ.

Determine:

a. The pressure of air inside the cylinder during the process.
b. The boundary work performed by the gas.
c. The combined work transfer by the shaft and electricity.

Answers

Answer:

Explanation:

From the given information:

The pressure of the air during the process = [tex]P_{atm} + P_{due \ to \ wt \ of \ piston}[/tex]

[tex]= 101 \ kPa + \dfrac{75 \ kg \times 9.8 \ m/s^2 \times \dfrac{1 \ N }{1 \ kg.m/s^2} }{\dfrac{\pi}{4}(0.2 \ m)^2} ( \dfrac{1 \ N }{m^2} \times \dfrac{1 \ kPa}{1000 \ n/m^2})[/tex]

The pressure of the air during the process = 124.42 kPa

The boundary work = P × ΔW

The boundary work = 124.42  kPa × (π/4) × (0.2 m)² × 0.25 m × (1 kJ/1 kPa.m³)

The boundary work = 0.977 kJ

The combined work transfer = [tex]W_{boundary} + \Delta U[/tex]

The combined work transfer = 0.977 + 3.109 kJ

The combined work transfer = 4.086 kJ

what is the mass of an object that is accelerating at a rate of 25m/s^2 and using 15 N of force

Answers

Answer:

mass = 0.6 kg

Explanation:

Given

Acceleration (a) = 25 m/s²

Force (F) = 15 N

Mass (m) = ?

We know

F = M * a

15 = m * 25

m = 15 / 25

m = 0.6 Kg

Hope it will help :)

The mass of an object that is accelerating at a rate of 25 m/s^2 and using 15 N of force is 0.6 Kg.

What is force?

A force is an effect that can alter an object's motion according to physics. An object with mass can change its velocity, or accelerate, as a result of a force. An obvious way to describe force is as a push or a pull. A force is a vector quantity since it has both magnitude and direction.

Given in the question,

Acceleration (a) = 25 m/s²

Force (F) = 15 N

Mass (m) = ?

We know

F = M * a

15 = m * 25

m = 15 / 25

m = 0.6 Kg

The mass of an object that is accelerating at a rate of 25 m/s^2 and using 15 N of force is 0.6 Kg.

To learn more about force refer to the link:

brainly.com/question/13191643

#SPJ2

Communication satellites are placed in a geosynchronous orbit, i.e., in a circular orbit such that they complete one full revolution about the earth in one sidereal day (23.934 h), and thus appear stationary with respect to the ground. Determine the altitude of these satellites above the surface of the earth in both SI and U.S. customary units.

Answers

Answer:

Explanation:

Let the radius of orbit of geostationary satellite be R .

Time period of satellite = 2πR / V₀ where V₀ is orbital velocity

T = 2πR / √gR

T= 2πR / √(GM / R )

T = 2πR¹°⁵ / √GM  

R¹°⁵ = T x √GM  / 2π

T = 23.934 h = 23.934 x 60 x 60 s = 86126.4 s

R¹°⁵ = 86126.4 x √ ( 6.67 x 10⁻¹¹ x 5.972 x 10²⁴ )  / 2π

= 86126.4 x √ ( 398.33 x 10¹²  )  / 2π

= 86126.4 x 19.95 x 10⁶  / 2π

= 273.428 x 10⁹

R = 42.92 x 10⁶ m

= 42920 km

Radius of orbit = 42920 km

radius of earth = 6370 km

Altitude of satellite = 42920 - 6370 = 36550 km .

In US customary unit = 36550 x 10³ /.9144 yards

= 36550 x 10³ /(.9144 x 1760 ) miles

= 22771 miles .

Which of the following choices is the best example of potential energy?

Answers

Answer:

A basketball sitting still in a players hands

Explanation:

The other 3 answers have the ball in motion (going towards the basket, bouncing, and rolling) so that would be kinetic energy.

When the basketball is sitting in the player's hands, it has the potential to be in motion.

Answer:

it is D not B it D

Explanation:

attraction is seen between the poles of two bar magnet in the case of​

Answers

Answer:

he magnetic field of a bar magnet is strongest at either pole of the magnet. It is equally strong at the north pole when compared with the south pole. The force is weaker in the middle of the magnet and halfway between the pole and the center

Explanation:

A shuttle bus slows down with an average acceleration of -2.4 m/s2. How long does it
take the bus to slow from 9.0 m/s to rest?

Answers

Answer:

[tex]\boxed {\boxed {\sf 3.75 \ seconds }}[/tex]

Explanation:

Average acceleration is found by dividing the change in acceleration by the time.

[tex]a=\frac{ v_f-v_i}{t}[/tex]

The shuttle bus has an acceleration of -2.4 meters per square second. It slows from 9.0 meters per second to rest, or 0 meters per second. Therefore:

[tex]a= -2.4 \ m/s^2 \\v_f= 0 \ m/s \\v_i= 9 \ m/s[/tex]

Substitute the values into the formula.

[tex]-2.4 \ m/s^2=\frac{0 \ m/s - 9 \ m/s}{t }[/tex]

Solve the numerator.

[tex]-2.4 \ m/s^2 = \frac{-9 \ m/s}{t}[/tex]

We want to solve for t, the time. We have to isolate the variable. Let's cross multiply.

[tex]\frac{-2.4 \ m/s^2}{1} = \frac{-9 \ m/s}{t}[/tex]

[tex]-9 \ m/s *1= -2.4 \ m/s^2 *t[/tex]

[tex]-9 \ m/s=-2.4 m/s^2*t[/tex]

t is being multiplied by -2.4. The inverse of multiplication is division, so divide both sides by -2.4

[tex]\frac{-9 \ m/s }{-2.4 \ m/s^2} =\frac{ -2.4 \ m/s^2*t}{-2.4 \ m/s^2}[/tex]

[tex]\frac{-9 \ m/s }{-2.4 \ m/s^2} =t[/tex]

[tex]3.75 \ s=t[/tex]

It takes 3.75 seconds.

point.
4.
i. Explain why a particle moving with a constant speed along a circular
path has a radial acceleration.
ii. Show that the acceleration of a body moving in a circular path of
radius r with uniform speed v is → and draw a diagram to show the
direction of the acceleration.
2
iii. Show that the expression à = † is dimensionally correct.​

Answers

Explanation:

Explanation: When a particle moves along a straight path, then the radius of curvature is infinitely great. This means that v2/r is zero. Explanation: When a particle moves with a uniform velocity, then dv/dt will be zero.

PLZZZZ HELPPPPPPPPPppppp​

Answers

What grade are you in?!!??

The physics of wind instruments is based on the concept of standing waves. When the player blows into the mouthpiece, the column of air inside the instrument vibrates, and standing waves are produced. Although the acoustics of wind instruments is complicated, a simple description in terms of open and closed tubes can help in understanding the physical phenomena related to these instruments. For example, a flute can be described as an open-open pipe because a flutist covers the mouthpiece of the flute only partially. Meanwhile, a clarinet can be described as an open-closed pipe because the mouthpiece of the clarinet is almost completely closed by the reed.
Consider a pipe of length 80.0 cm open at both ends. What is the lowest frequency f of the sound wave produced when you blow into the pipe?

Answers

Answer:

Explanation:

Lowest frequency will be the fundamental frequency . For fundamental note

λ /2 = L where λ is wavelength of sound produced and L is length of open end pipe .

Given L = 80 cm

λ /2 = 80

λ = 160 cm .

= 1.6 m

frequency of note = velocity of sound / wavelength

= 330 / 1.6

= 206.25 Hz .

206 Hz approx.

How can you drop two eggs the fewest amount of times, without them breaking?

Answers

Because the shell didn’t crack.

I hope this helps.

Answer:

get 2 jugs of water put an egg in each one drop the jugs with parachutes on them in long grass on a sunny non windy day

Explanation:

egg+ground=broken

egg-ground= egg+air

egg+air=unbroken

egg+water= egg+wet

egg+water= unbroken

egg+egg= 2 egg

egg+egg+air= egg+egg+unbroken+unbroken

egg+egg+unbroken+unbroken=(egg+unbroken)2

longgrass+egg= 40%unbroken+60broken+egg

longgrass+egg+egg=20%unbroken+80%broken+2egg

ground+water=mud

mud+egg=unbroken+egg+muddy

air+water=raining

egg+raining+air=wet+egg+slip+50%broken+50%unbroken

ask if need more proof

A vertical wire carries a current straight up in a region of the magnetic field directed north. What is the direction of the magnetic force on the current due to the magnetic field

Answers

Answer:

The direction of the force on the vertical wire is towards the East or right.

Explanation:

Using Fleming's right hand rule, the current is the middle finger pointing straight up, the magnetic field is the fore-finger pointing Northwards and then the thumb is the direction of the force on the vertical wire.

Following these conventions, the thumb points towards the East. So, the direction of the force on the vertical wire is towards the East or right.

Which statement accurately describes a relationship between parts of the
universe?
O A. There are millions of nebulae in a star.
O B. There are thousands of universes in a galaxy.
C. There are trillions of galaxies in the universe.
O D. There are billions of galaxies in a solar system.

Answers

Answer:

C. There are trillions of galaxies in the universe.

Explanation:

A. is wrong as nebulae are found inside galaxies and inside the universe, not inside stars.

B. is wrong because there are trillions of galaxies in the universe, not the latter.

D. The solar system consists of the eight planets, the Sun, comets, meteors, dwarf planets, and is inside the Milky Way galaxy and thus cannot have galaxies inside it.

Please give Brainliest

Answer:

C.

Explanation:

There are trillions of galaxies in the universe.

How far can a bus carrying small children, travel at a rate of 60 km per hour travel in 2 1/2 hours?

Answers

150km

Explanation:

speed = 60km/hr.time = 2¹/2 hr = 5/2 hrdistance = speed × time = 60 ×5/2 = 150km

MARK ME AS BRAINLIST

who has brown hair and brown eyes but is a boy

Answers

Answer:

I have strawberry blonde/brown hair blue eyes and a girl lol

Explanation:

Which two statements help explain why digital storage of data is so reliable?

A. Memory chips are sturdy.

U B. Digital data usually deteriorate over time.

C. It is usually possible to recover data from a memory chip even

when the device containing it is broken.

D. Digital data are easier to copy than analog data are, making them

more accessible to thieves.

Answers

Answer:

A. Memory chips are sturdy.

C. It is usually possible to recover data from a memory chip even when the device containing it is broken.

Explanation:

Digital storage of data refers to the process which typically involves saving computer files or documents on magnetic storage devices usually having flash memory. Some examples of digital storage devices are hard drives, memory stick or cards, optical discs, cloud storage, etc.

A reliable storage ensures that computer files or documents are easily accessible and could be retrieved in the event of a loss.

The two statements which help explain why digital storage of data is so reliable are;

A. Memory chips are sturdy: they are designed in such a way that they are compact and firm.

C. It is usually possible to recover data from a memory chip even when the device containing it is broken.

Answer:

A and C

Explanation:

got it right on a p e x

A radio transmitting station operating at a frequency of 125 MHz has two identical antennas that radiate in phase. Antenna B is 9.05 m to the right of antenna A. Consider point P between the antennas and along the line connecting them, a horizontal distance x to the right of antenna A. For what values of x will constructive interference occur at point P?

Answers

Answer:

Explanation:

The formula for frequency is:

[tex]f = \dfrac{c}{\lambda}[/tex]

If we make [tex]\lambda[/tex] the subject; we have:

[tex]\lambda = \dfrac{c}{f}[/tex]

[tex]\lambda = \dfrac{3\times 10^6 \ m/s}{125 \ MHz (\dfrac{10^6 \ Hz}{1 \ MHz})}[/tex]

[tex]\lambda = 2.4 \ m[/tex]

Let assume that there is a point P between antenna A  to B.

where;

A to B = 9.05

A to P = x  and

P to B = 9.05 - x

Then, the condition for the constructive inteference is:

Δx = nλ

x - (9.05 - x) = nλ

2x - 9.05 = n(2.4)

So, we need to start assigning values to n so that the value of x becomes less than or equal to 9.05 m

If n = -1

Then;

2x - 9.05 = (-1)(2.4)

x = 3.325 m

If n = -2

Then;

2x - 9.05 = (-2)(2.4)

x = 2.125 m

If n = -3

Then;

2x - 9.05 = (-3)(2.4)

x = 0.925 m

If n = 0

Then;

2x - 9.05 = (0)(2.4)

x = 4.525 m

If n = 1

2x - 9.05 = (1)(2.4)

x = 5.725 m

If n = 2

Then;

2x - 9.05 = (2)(2.4)

x = 6.925 m

Hence, there exist 7 points in which constructive interference occurs.

pls help me this is a major SOS pls help pls btw this is IXL

Answers

Explanation:

the object with the higher temperature has greater thermal energy

So the answer is

the stick of butter with less thermal energy.

Hope it will help :)

Answer:

The stick of butter with less thermal energy

Explanation:

I am pretty sure

Calculate the ratio of the drag force on a passenger jet flying with a speed of 1200 km/h at an altitude of 10 km to the drag force on a prop-driven transport flying at one-fourth the speed and half the altitude of the jet. At 10 km the density of air is 0.38 kg/m3 and at 5.0 km it is 0.67 kg/m3. Assume that the airplanes have the same effective cross-sectional area and the same drag coefficient C. (drag on jet / drag on transport)

Answers

Answer:

[tex]2.267[/tex]

Explanation:

Drag force is given by

[tex]F=\dfrac{1}{2}\rho Av^2C[/tex]

C = Drag coefficient is constant

A = Area is constant

[tex]v_1[/tex] = Velocity of the passenger jet = 1200 km/h = [tex]\dfrac{1200}{3.6}\ \text{m/s}[/tex]

[tex]v_2[/tex] = Velocity of the prop plane = [tex]\dfrac{1}{4}v_1[/tex]

[tex]\rho_1[/tex] = Density of the air where the jet was flying = [tex]0.38\ \text{kg/m}^3[/tex]

[tex]\rho_2[/tex] = Density of the air where the prop plane was flying = [tex]0.67\ \text{kg/m}^3[/tex]

[tex]F\propto \rho v^2[/tex]

[tex]\dfrac{F_1}{F_2}=\dfrac{\rho_1 v_1^2}{\rho_2 v_2^2}\\\Rightarrow \dfrac{F_1}{F_2}=\dfrac{0.38 v_1^2}{0.67 (\dfrac{1}{4}v_1^2)}\\\Rightarrow \dfrac{F_1}{F_2}=2.267[/tex]

The ratio of the drag forces is [tex]2.267[/tex].



The electric field from two charges in the plane of the paper is represented by the dashed lines and arrows below.

Select a response for each statement below. (Use 'North' towards top of page, and 'East' to the right)


The magnitude of the E-field at Ris .... than at M.

The force on a (+) test charge at P is zero.

The magnitude of the charge on the left is .... that on the right.

The force on a (+) test charge at L is directed ....

The force on a (-) test charge at J is directed

The force on a (-) test charge at N is directed ....

The sign of the charge on the right is negative.

Answers

Answer:

a) electric field at point P must be zero

b) harged must be positive

c) force ais in the direction of the electric field

d)  force is in the opposite direction to the electric field

e)  force is in the opposite direction to the field

Explanation:

After reading your exercise, it is unfortunate that the diagram did not come out, but we are going to answer the questions in general.

a) force on a charge (+) is zero

this implies that the electric field at point P must be zero

        F = q E

b) the magnitude of the charge on the left is on the right

this indicates that the charged must be positive since the lines must exit the charge

c) force on load directed towards (direction not indicated)

since the charge is positive the force at point L is in the direction of the electric field at this point

d) force on test load (-) does not indicate direction

The force on a negative charge is in the opposite direction to the electric field at point J

e) Force on a test load (-) at point N

the force is in the opposite direction to the field at point N

The speed of propagation of the action potential (an electrical signal) in a nerve cell depends (inversely) on the diameter of the axon (nerve fiber). If the nerve cell connecting the spinal cord to your feet is 1.3 m long, and the nerve impulse speed is 33 m/s, how long (in s) does it take for the nerve signal to travel this distance?

Answers

Answer:

Explanation:

Speed of electrical nerve signal = 33 m /s

Distance travelled = 1.3 m

time taken = distance / speed

= 1.3 / 33  

= .039 s

= 39 ms ( millisecond )  .

Which one of Newton’s Laws best explains a bottle flip?

Answers

Answer:

the 2nd law-

Hope this helps <3

Explanation:

How long will it take an object traveling at 90 kilometers per hour to travel 910 kilometers?

Answers

Explanation:

time = distance / velocity

We know that distance = 910 km and velocity = 90 km/h.

t = d / v

t = 910 km / 90 km/h

t = 10.11 hrs

The object traveled for 10.11 hours long. Hope this helps, thank you !!

|:Give one word answer
1. An object that allows whole light to pass through it _______​

Answers

Answer:

Translucent object

Explanation:

who is bill cypher and what is his origin?

Answers

Answer:

Bill Cipher is the true main antagonist of Gravity Falls. He is a Dream-Demon with mysterious motives and seems to have a vendetta against the Pines family, especially his old rival Stanford Pines

Explanation:

Concept Simulation 4.1 reviews the central idea in this problem. A boat has a mass of 4490 kg. Its engines generate a drive force of 4520 N due west, while the wind exerts a force of 890 N due east and the water exerts a resistive force of 1210 N due east. Take west to be the positive direction. What is the boat's acceleration, with correct sign

Answers

Answer:

-0.54m/s²

Explanation:

According to Newton's second law of motion

F = ma

Force = mass * acceleration

Given

Mass m = 4490kg

Take the sum of forces

Sum of force along the east = 890+1210 = 2100N

Sum of forces along the west = -4520N

Net force = -4520+2100

Net force = -2420N

Acceleration = Net force/Mass

Acceleration = -2420/4490

Acceleration = -0.54m/s²

Hence the boat acceleration is -0.54m/s²

If a wave has a speed of 1000 m/s and frequency of 500 Hz, what is the wavelength?

• 1500 Hz
• 2 m
• 0.05 m

Answers

Answer:

2 m

Explanation:

speed=frequency×wavelength

wavelength=speed/frequency

wavelength=1000/500

=2 m

A long, circular aluminum rod is attached at one end to a heated wall and transfers heat by convection to a cold fluid. If the diameter of the rod is doubled, by how much would the rate of heat removal change

Answers

Complete question is;

A long, circular aluminum rod is attached at one end to a heated wall and transfers heat by convection to a cold fluid. If the diameter of the rod is doubled, by how much would the rate of heat removal change?

Answer:

182.84 %

Explanation:

Formula for rate of heat transfer of an infinite log fin is given as;

q_f1 = (π/2) × (hk)^(½)) × D^(3/2)) × (T_b - T_∞)

Where D is diameter.

Now, if the diameter of the rod is doubled, it means Diameter is now 2D.

Thus;

q_f2 = (π/2) × (hk)^(½)) × (2D^(3/2)) × (T_b - T_∞)

To find how much the rate of heat removal will change, we will calculate as follows;

((q_f2/q_f1) - 1) × 100

Plugging in the relevant expressions, we have;

([[(π/2) × (hk)^(½)) × ((2D)^(3/2)) × (T_b - T_∞)]/[(π/2) × (hk)^(½)) × (D^(3/2)) × (T_b - T_∞)]] - 1) × 100

Upon simplifying, we have;

(((2D)^(3/2))/(D^(3/2)) - 1) × 100

((2^(3/2)) - 1) × 100

This gives;

182.84 %

Two students are on a balcony a distance h above the street. One student throws a ball vertically downward at a speed vi; at the same time, the other student throws a ball vertically upward at the same speed. Answer the following symbolically in terms of vi, g, h, and t. (Take upward to be the positive direction.)
(a) What is the time interval between when the first ball strikes the ground and the second ball strikes the ground?
?t = ______
(b) Find the velocity of each ball as it strikes the ground.
For the ball thrown upward vf = ______
For the ball thrown downward vf = ______
(c) How far apart are the balls at a time t after they are thrown and before they strike the ground?
d = _______

Answers

Answer:

Explanation:

 a )

Time for first ball to reach top position

v = u - gt

0 = vi - gt

t = vi / g

Time to reach balcony  while going downwards

= vi /g

Total time = 2 vi / g

Time to go down further to the ground = t₁

Total time = 2 vi / g + t₁

Time for the other ball to go to the ground = t₁

Time difference = ( 2 vi / g + t₁ ) - t₁

= 2vi / g .

( b )

v² = u² + 2gh

For both the throw ,

final displacement = h , initial velocity downwards = vi

( For the first ball also  , when it go down while passing the balcony , it acquires the same velocity vi but its direction is downwards.)

vf² = vi² + 2gh

vf = √ ( vi² + 2gh )

(c )

displacement of first ball after time t

s₁ = - vi t + 1/2 g t²  [ As initial velocity is upwards , vi is negative ]

displacement of second ball after time t

s₂ = vi t + 1/2 g t²

Difference = d =  s₂ - s₁

= vi t + 1/2 g t² - ( - vi t + 1/2 g t² )

d = 2 vi t .

what is the formular for force​

Answers

Answer:

f=m*a

Explanation:

The formula for force says force is equal to mass (m) multiplied by acceleration (a)

Other Questions
Increases partial thromboplastin time, but not prothrombin time? a. enoxaparin b. dabigatran c. rivaroxaban d. warfarin The main difference between the related constrained level of diversification and the related linked level of diversification is:__________ The only source of light in a room is the lightbulb shown. An opaque disk is placed in front of the bulb. A screen is then placed successively at positions A, B, and C. At which screen position(s) does the disk cast a shadow that is completely dark at the center Cian, a college student, wants to graduate before getting married. He feels tension between his religion's expectation to avoid premarital sex and his college friends' expectations that he be sexually active while in school. Cian is experiencing An equimolar mixture of two optical isomers is called a ________. An equimolar mixture of two optical isomers is called a ________. enantiomer achiral diastereomer structural isomer racemic mixture we were lucky because it was sunny every day french duolingo Question (iv) Sahil: Meet him, (a)............ (his, him, he) is (b)........(my, me, me ) brother. Rohan: You resemble (c).......... (each,every,all ) (d).........(other, another many ) Sahil: No, you are wrong, (e)....... (neither.either, the few) of us resembles. In fact, there is hardly (f)............ (some,any several) resemblance. Regarding the measurement of capacity, when a firm provides a relatively small range of standardized products and services: PLEASE ANSWER QUICK What is the renewability of geothermal power? It is a nonrenewable energy source. It is an unlimited, clean energy source. It can be replenished by splitting nuclei. It can use the same fuel cells repeatedly. to prevent injury while maintaining equipment make sure the equipment is Describe a presentation or a briefing you have conducted recently. how did you adapt it to your public? how did your auditors react? what did you get out of it? Natural formation processes include such activities as plowing, building structures, or making tools. Confused on this so please help: optimize the equation p = 2x + y using the constraints. what is the maximum? choices: a. 7 b. -1 c. 5 d. 13 Simplify: Simplify: StartRoot StartFraction 27 x Superscript 12 Baseline Over 300 x Superscript 8 Baseline EndFraction EndRoot Cory gives his friend money to buy a cheeseburger since he forgot his wallet at home, but expects to be repaid. This represents the financial service of: Can somebody help me with these 2 questions? Use the law of syllogism to complete the conclusion. statement 1: if p, then q. statement 2: if q, then r. conclusion: if p, then... A study showed that low-intensity shock therapy reduces pain levels in patients with lupus. During each session, electrodes were placed on the pain site indicated by the patient. Pain reduction was measured through self-reporting after each session.Another study is being designed to examine whether low-intensity shock therapy also reduces pain in patients suffering from bulging disks in the thoracic region of the back. Two hundred female patients are subjects in the new study.Part A: What is an appropriate design for the new study? Include treatments used, method of treatment assignment, and variables that should be measured. (4 points)Part B: If the study consisted of 100 male and 100 female patients instead of 200 female patients, would you change the study design? If so, how would you modify your design? If not, why not? (4 points)Part C: Could your design be double-blind? Explain. (2 points) Which cultures music do you prefer and why (African, Indian, Japanese, or Latin)? Cost of Goods Sold = Revenue - Operating Profit, is it right? I have report about the unilever financial result, but I haven't seen the number of the cost of goods sold in its sheet!