When two bodies at equal temperature are brought in contact with each other then no heat flows between them and they are said to be in thermal equilibrium.
When bodies in contact are in thermal equilibrium then they have the same?When the engine temperature eventually reaches the same level as the ambient temperature, thermal equilibrium has taken place. After being placed on the table and waiting a short while, a cup of hot tea cools to the same temperature as its surroundings.
This is where thermal equilibrium occurs. the set temperature at which all of a solid's mass melts. When the solid turns into a liquid, both the solid and the liquid coexist in the thermal equilibrium.
The individual drove himself to his location. The engine temperature was excessively high during that time, but it eventually dropped to the air temperature outside. When the engine temperature eventually reaches air temperature, thermal equilibrium has occurred.
To learn more about thermal equilibrium refer to:
https://brainly.com/question/14556352
#SPJ1
A(1) and (2) only of the following bodies are at thermal equilibrium when being put into contact. i.e. (1) A glass of water of internal energy E at 20 °C (2) Alcohol with unknown internal energy at 20 °C .
What is thermal equilibrium?When two physical systems are linked by a channel permeable to heat, they are said to be in thermal equilibrium if there is no net transfer of thermal energy between them. The zeroth law of thermodynamics is observed during thermal equilibrium.As internal energy is measured in terms of the body temperature, when two bodies are in thermal equilibrium, their internal energies will also be equal.
to know more about internal energy visit
https://brainly.com/question/11278589
#SPJ1
How much work does the battery connected to the 21.0-ohm resistor perform in one minute? The voltage of the battery is 12.0V and the internal resistance of the battery is 3.00 ohm.
The work performed by a battery is 310 J according to the formula W= Pt and the provided data.
In an electrical circuit, what is the work?The formula for the electrical work is W = Q V. In this case, the electric potential, V, is expressed in volt, the electric charge, Q, is expressed in coulombs, and the work done, W.
The work performed in an electronic circuit may be computed using the formula
W=Pt,
where P=IV is the supplied electrical power and t is the time.
W= Pt =I V t=V²t/ Req
= V²t/ R + r
therefore
W= (12.0V)²(60s)/21.0Ω+3.00Ω
= 310 J
To know more about work visit :
brainly.com/question/13542047
#SPJ1
a box of chocolate bars weighs 180N. Its base has an area of 0.09m2. what pressure does it exert on the ground
Answer:
2000
Explanation:
180/0.09
=2000
pressure=force/area
if the bat and softball are in contact for 0.80m/s, what is the average force that the bat exerts on the ball
The changes in the momentum of the ball and the time over which that change occurs. The formula for average force is: average force = change in momentum/time.
Calculation-Given: The ball's mass is 0.144 kilogram.
speed v = 38 m/s, shift in momentum presently
P = m v- ( - mv) ( - mv)= 2 mv
=2 x (0.144) x (38) (38)
= 10.944 kg-m/s
t Impulse J=F.
The impulse is equivalent to the change in momentum.
J = 10.944 kg-m/s
What forces are at play when a baseball bat strikes a fastball?Think about how a baseball bat and a ball interact, for instance. The bat forces the ball to the right while the baseball forces the bat to the left. The action-reaction force pair is made up of these two forces acting on two different objects combined.
to know more about force here:
https://brainly.com/question/29781083
#SPJ4
Pitch a baseball horizontally at 38.0 m/s weighing 0.144 kg. The baseball moves in the opposite direction and at the same speed after being struck by the bat. What is the ball's change in momentum? What kind of impetus does the bat deliver? What was the average force the bat applied to the ball during the 0.80 milliseconds that they were in contact?
Which of the following types of microscopes reveals the surface features of small molecules? - a confocal microscope - a fluorescent microscope - a transmission electron microscope (TEM) - an atomic force microscope
The types of microscopes that reveals the surface features of small molecules is an atomic force microscope.
The Atomic Force Microscope (AFM) is useful for imaging the surface topography of living, soft materials in their natural settings. It can be used to examine the inherent elastic modulus and receptor-ligand interactions of cells and extracellular matrix, among other mechanical properties. SEM pictures can investigate surface features that are several tenths of a nanometer in size, but AFM resolution is less than 0.1 nm. As a result, AFM can discern objects on flat surfaces with molecular dimensions.
To learn more about Atomic Force Microscope (AFM), click here:
https://brainly.com/question/17781933
#SPJ4
If an object takes 5 seconds to fall off a building, how high is the building?
A fish introduces more air into its swim bladder so that it rises toward the surface of the water. Which of the following statements best describes the situation? A The fish decreased its buoyant force by decreasing its density. B The fish increased its buoyant force by increasing its density. с The fish increased the buoyant force by reducing its density.
The situation will be describe with:
C. The fish increased the buoyant force by reducing its density.
THE SWIM BLADDERA swim bladder is an internal organ that some fish use to control their buoyancy. The fish can adjust the amount of gas in the swim bladder to make itself more or less dense than the water around it. In order to rise toward the surface of the water, the fish would need to decrease its density relative to the water, which it can do by increasing the amount of air in its swim bladder. This increase in air in the swim bladder reduces the fish's density, which in turn increases its buoyancy and allows it to rise to the surface.
There are different ways that a fish can control its buoyancy, and different species of fish may have different adaptations for doing so. Some fish may have other organs or structures that can be used to control buoyancy, such as lipids in their body tissue, or fins that can be used to control their position in the water.
Additionally, some fish may have the ability to change their shape or size in order to control their buoyancy, such as by swallowing air or by compressing their swim bladder. However, in general, the most common way for fish to control buoyancy is by adjusting the amount of gas in their swim bladder.
Learn more about swim bladder here:
https://brainly.com/question/14431269
#SPJ4
A student carefully measures the time it takes for a turtle to move 10.0 m. He gets a value of 4218.6 s. However he discovers that the stopwatch had already been running for about 300 s before the turtle started to move. How long did it take the turtle to go 10.0 m
The turtle traveled 10 meters in 3,918.6 seconds using simple subtraction.
What does subtracting in math mean?In mathematics, to subtract is to eliminate something from set of things or a group of things. When we remove from the group, the number of items falls or gets less. The minuend, forces at play, and difference are the elements of a subtraction problem.
It involves calculating the distinction between two numbers. The icon looks like this: (minus). In this operation, we take a particular number then split it by a fewer group. In other words, we divide one integer by another. Click here for some difficult addition and subtraction sums.
He gets a value of 4218.6 s
he discovers that the stopwatch had already been running for about 300 s
Time taken by turtle = 4218.6 - 300
= 3918.6 s
To learn more about subtraction from given link
https://brainly.com/question/28467694
#SPJ4
a 0.30g fly moving at 1.5ms-1 is trappedby a spiders web the fly comes to rest in a time of 0.40s calculate the magnitude of the change in momentum if the fly and the average firce exerted by the web on the fly
Answer:
Magnitude of the change in momentum = 0.45kgms-1
Force exerted = 1.13N
Explanation:
The magnitude of the change in momentum of the fly can be calculated using the equation Δp = mv, where m is the mass of the fly and v is the velocity of the fly. In this case, the fly has a mass of 0.30g and an initial velocity of 1.5ms-1. Therefore, the change in momentum of the fly is
Δp = (0.30g) x (1.5ms-1) = 0.45kgms-1.
The average force exerted by the web on the fly can be calculated using the equation F = Δp/Δt, where F is the average force, Δp is the change in momentum of the fly, and Δt is the time taken for the fly to come to rest. In this case, the change in momentum of the fly is 0.45kgms-1 and the time taken for the fly to come to rest is 0.40s. Therefore, the average force exerted by the web on the fly is
F = (0.45kgms-1)/(0.40s) = 1.13N.
Eileen is holding a pillow with a mass of 0.30 kg when Stephanie decides she wants it and tries to pull it way from Eileen. If Stephanie pulls horizontally on the pillow with a force of 10.0 N and Eileen pulls with a horizontal force of 11.0 N, what is the magnitude of the net acceleration of the pillow
The magnitude of the net acceleration of the pillow is 3.333 m/s^2 .
How do you determine the magnitude of the net acceleration?To determine the magnitude of the net acceleration of the pillow, we can use Newton's Second Law of Motion, which states that the net force acting on an object is equal to the mass of the object multiplied by its acceleration:
Fnet = ma
where
Fnet = net force acting on the pillow
m = mass of the pillow (0.30 kg)
a = acceleration of the pillow
Fnet = FStephanie - FEileen = 10 N - 11 N = -1 N
So, the net force acting on the pillow is -1N
Now, we can use Newton's Second law to find the acceleration of the pillow
a = Fnet/m = -1 N / 0.3 kg = -3.333 m/s^2
Therefore, the magnitude of the net acceleration of the pillow is 3.333 m/s^2 .
To know more about Acceleration visit :
brainly.com/question/12550364
#SPJ4
A certain light truck can go around a flat curve having a radius of 150 m with a maximum speed of 34.5 m/s. With what maximum speed can it go around a curve having a radius of 60.0 m
With 20.23 ms⁻¹, maximum speed can it go around a curve having a radius of 60.0 m
What's the maximum speed?The highest rate of speed a person can reach is called maximum speed. When athletes alter the magnitude (how quickly they are moving) or direction (or both) of their motion, or both, their acceleration changes as well since acceleration is related to velocity, which has both a magnitude and a direction connected with it.
ac max = V² max / R ....(1)
Inserting given values we get
ac, max = (34.5)² / 150 = 7.935 ms⁻²
For a changed radius of the curve of 60.0 m, the maximum safe speed from (1) becomes
Unew, max= √ac, max R new
Unew, max = √6.826 x 60
Unew, max 1 = 20.23 ms⁻¹, rounded to one decimal place.
To learn more about speed from given link
https://brainly.com/question/13262646
#SPJ4
What causes high latency?
A low bandwidth will result in a high ping (delay) and, most likely, lag while you're playing. It will also affect how quickly data is delivered and then received.
When latency is high, what does that mean?Because of the temporal lag caused by high latency, gaming might be much less enjoyable. It is essential because low latency allows for more fluid gameplay. Typically, a latency (or ping) of 40–60 milliseconds (ms) or less is considered to be acceptable.
What happens when latency is reduced?Your website resources will load more quickly if server latency is reduced, which will also improve the time it takes for visitors to load all of your pages.
To know more about latency visit:-
https://brainly.com/question/14894222
#SPJ4
When a satellite is a distance R from the center of the Earth, the force of gravity on the satellite is F. What is the gravitational force on the satellite when its distance from the center of the Earth is 3R
When a satellite is 3R from Earth's center, its gravitational force is equal to F/9.
What do you mean by gravitational force?Any pair of mass-containing objects will gravitationally pull toward one another. It mentions the gravitational force. The force will always applied along the line joining the two mass in the direction of the second mass, based on the formula F=Gm1m2r2.
Given that the foece on the satellite due to earth gravity is F
(At a distance R from center of Earth)
Initial separation between the satallite and Earth is R
Final separation between the satallite and Earth is 3R
The force on the satallite due to earth is
F= [tex]\frac{GMm}{r^{2} }[/tex]
Here M is mass of earth and m is mass of satellite
if the distance between satellite and earth changed to 3R
the force on the satellite due to earth is
F'=[tex]\frac{GMm}{3R^{2} }[/tex]
F'=[tex]\frac{GMm}{9R^{2} }[/tex]
F'=F/9
To know more about gravitational force visit:
brainly.com/question/12528243
#SPJ4
A 26 kg crate initially at rest on a horizontal floor requires a 70 N horizontal force to set it in motion. Find the coefficient of static friction between the crate and the floor.
The coefficient of static friction between the crate and the floor is calculated to be 0.275.
The frictional force when an object moves on the horizontal surface is given as,
Ff = μ N
where, N is the normal force
μ is the coefficient of static or kinematic friction
If no forces other then the weight and the normal are acting upon the y-direction, then the weight and the normal force are equal in magnitude.
N = W = m g
Given that,
Mass of the crate = 26 kg
Frictional force Ff = 70 N
Weight of the crate = 26 × 9.8 = 254.8 N
The normal force is 254.8 N.
The coefficient of static friction μ = Ff /N = 70/254.8 = 0.275
Thus, the coefficient of static friction between the crate and the floor is 0.275.
To know more about friction:
https://brainly.com/question/20162979
#SPJ4
To help me become a detective, would it matter if I did triple science or not?
Answer:
No, it would not matter if you did triple science or not in terms of becoming a detective. However, it is important to have a good academic background and a strong understanding of the law and criminal justice system. Additionally, having good communication and problem-solving skills is also beneficial.
Explanation:
A series circuit has 1200 ohms of total resistance with 12 v as the power supply. What is the total of the circuit
According to Ohm's Law, the total current flowing through a circuit with a resistance of 1200 ohms and a 12 V power supply is equal to 0.01 ampere.
Ohm's law is what?Electric current is inversely correlated with resistance according to Ohm's Law and proportionate to voltage. 'The law can be expressed mathematically as V = IR, in which 'V' is the voltage variation 'I' is the flowing current in amps, & the resistance (R) in ohm.
Given data :
Resistance = 1200 ohm
power supply = 12 V
By using Ohm's law
V = I × R
I = V / R
I = 12 / 1200
I = 0.01 ampere.
To know more about Ohm's law visit :
https://brainly.com/question/1247379
#SPJ1
How will you explain the effect of the absorption and release of heat on the kinetic energy and arrangement of particles of matter?
According to the kinetic theory of matter, changes in heat energy allow for phase transitions between solids, liquids, and gases.
When something is heated, the particles inside move faster and have more energy. When an object warms up, its atoms and molecules gain kinetic energy. When something is heated, its constituent atoms or molecules accelerate in their motion. Matter's kinetic energy can be quickly and easily increased.
When an object warms up, its atoms and molecules gain kinetic energy. The atomic or molecular motions of matter increase with temperature. Lifting a particle's kinetic energy is a breeze. When a substance absorbs heat, the inter-particle bonds in it weaken and break, resulting in a phase transition. If the particles aren't moving faster, there can't be any more heat.
Want to know more about kinetic energy visit the link which is given below;
https://brainly.com/question/26472013
#SPJ4
Imagine some cosmic catastrophe jolts Earth so that its axis is perpendicular to the orbital plane between Earth and the sun. The most obvious effect of this change would be ____.
Any cosmic catastrophe jolts the Earth so its axis is perpendicular to the orbital plane between Earth and the sun. Then, the significant effect will be the elimination of the variation of seasons.
A cosmic Catastrophe is a thought experiment in which the sun disappears in an instant. A Planetary Response gradually creates a supranational agency to protect life on Earth from natural threats from terrestrial (pandemics, mega volcanoes, major earthquakes, etc.) and celestial bodies (comets, asteroids, meteor storms, etc.). I am asking you to Variation in a time series within a year that repeats more or less regularly. Seasonal variations can occur due to temperature, precipitation, holidays, seasonal cycles, or holidays. Seasonality is defined as the cyclical changes in food and agricultural labor availability caused by climate change in rural areas of the least developed countries (LDCs).
Learn more about the catastrophe in
https://brainly.com/question/7930785
#SPJ4
The work you do when pushing a shopping cart twice as far while applying double the force is
A) half as much
.B) twice as much.
C) four times as much.
D) the same amount.
The work you do when pushing a shopping cart twice as far while applying double the force is twice as much as force.
What is Force?
A push or pull that an object experiences as a result of interacting with another item is known as a force. Every time two items interact, a force is exerted on each of the objects. The force is no longer felt by the two objects when the interaction ends.
Contact forces are the kinds of forces that develop when two objects interact and appear to be in physical contact with one another. Frictional forces, tensional forces, normal forces, air resistance forces, and applied forces are a few examples of contact forces.
Forces that come from action at a distance.
Therefore, The work you do when pushing a shopping cart twice as far while applying double the force is twice as much as force.
To learn more about Forces, refer to the link:
https://brainly.com/question/13191643
#SPJ1
An astronaut (86 kg) on a spacewalk (outside of the shuttle) throws Space Cat (4.8
kg) at a speed of 25 m/s, relative to the shuttle, at an angle of 40 degrees above horizontal
away from himself. What is the speed of the astronaut after launching our feline
superhero?
The speed of the astronaut after launching our feline superhero is 1.4 m/s.
What is the speed of the astronaut?
The speed of the astronaut is determined from the principle of conservation of linear momentum.
Pi = Pf
where;
Pi is the momentum of the astronautPf is the momentum of the cat86vₓ = 4.8 x (25 cos40)
86vₓ = 91.9
vₓ = 91.9 / 86
vₓ = 1.07 m/s
The vertical component of the speed;
86vy = 4.8 x (25 sin40)
86vy = 77.1
vy = 77.1 / 86
vy = 0.9 m/s
The resultant speed of the astronaut is calculated as;
v = √ ( vₓ² + vy² )
v = √ ( 1.07² + 0.9² )
v = 1.4 m/s
Learn more about speed of astronaut here: https://brainly.com/question/29727760
#SPJ1
Does a heavier object go down a ramp faster?
A heavier object go down a ramp at a same pace as a lighter object go down a ramp because of gravitational force acting on it in a major form and the rolling tangential force acting on it in a smaller manner..
Rolling motion happens when an object roll over from a ramp or any other sloppy surface whether it is rough or smooth. many forces act on it at the same moment. also in many forces rolling tangential force and gravitational force is also acting on it at the same moment. in which the gravitational force is acting on it at a bigger pace and plays an important role in rolling of the object from the ramp or any other sloppy surface. hence, by this information we can firmly consider that a heavier object go down a ramp at a same pace as a lighter object go down a ramp because of gravitational force acting on it in a major form.
Learn more about Rolling motion:
brainly.com/question/29568301
#SPJ4
What is the mass of a softball if it hit the catcher's glove traveling at
48.7 m/s2 and struck with a force of 51.3-Newton?
Answer:
To solve this problem, you can use the formula F = ma, where F is the force applied to an object, m is the mass of the object, and a is the acceleration of the object. In this case, the force applied to the object is 51.3 newtons and the acceleration of the object is 48.7 m/s2. So, you can set up the equation like this:
51.3 newtons = m x 48.7 m/s2
To solve for the mass of the object, you can divide both sides of the equation by 48.7 m/s2:
51.3 newtons / 48.7 m/s2 = m x 48.7 m/s2 / 48.7 m/s2
This simplifies to:
1.05 kg = m
So, the mass of the softball is approximately 1.05 kilograms.
A body of ma 3kg and volume 4x10-4m3 hung from a balance graduated in newton. What i the reading of the balance when the body i in air
W=mg=(3)(9.8)=29.4N is the balance measurement for an airborne body. Scales of this kind include spring balances and newtons meters. They are frequently used to gauge the amount of force applied to an object.
What guiding principle guides the Newton spring balance?The spring balance operates according to Hooke's law. According to Hooke's law, a material's strain will increase in direct proportion to its applied stress up to its elastic limit.
The spring balance measures what?A straightforward and affordable way of measuring mass is offered by spring balances. The mass is suspended from a spring, and the spring's bending caused by the mass's downward gravitational pull is gauged against a scale.
To know more about spring balances visit :-
https://brainly.com/question/1597448
#SPJ4
A block of mass mm is initially at rest on a rough horizontal surface when a constant force FF is exerted on it, as shown. The block accelerates to the right and is moving with speed vv once it has moved a distance dd. Which of the following equations can be used to solve for the force of friction exerted on the block by the surface?
F m v2 А F-f= 2d B F-f=ma с F-f= mv2 2d D f-F = mv2 d E f-F = mv2 2d
Block B on the exterior f-F = ma c f-F = mv2 2d f-F = D = mv2 d f-F E f-F = v2 2d.
What is meant by mass surface?A thing's top, exterior, or outermost layer: Tropical rain forests once covered 10% of the earth's surface. The marble has a smooth, polished surface.
The surface of the picture is covered in little fissures. The bowl's exterior has a glossy finish. The wood was rough on the outside. Ice-covered roads ought to be avoided. The phrase "on the surface" describes how something seems, even if it isn't really the case.
The formulas F- f = mv2 / d can be used to determine the force of friction that the surface exerts on the block.
Briefing:
F - f = ma
a = v/t
t = d/v
F - f = m × v / t
F- f = m ×
F- f = m × v²/d
Therefore,
F- f = mv² / d
To learn more about mass surface refer to:
brainly.com/question/19385703
#SPJ4
What is better static or dynamic stretching?
Explanation:
This intense stretching method uses bouncing movements to push your body beyond its normal range of motion. Whereas static stretches are performed slowly and gradually, the ballistic method stretches muscles much farther and faster. You can do many of the same stretches as ballistic or static stretches.
is/are defined in the NEC as the conductors and equipment for delivering electric energy from the serving utility to the wiring system of the premises served
The cables and machinery used to transport electric energy from the supplying utility to the wiring system of the premises served are referred to as "service" in the NEC. The Service Point is the location where the customer's premises wiring starts and the utility supply terminates.
is the distance between the utility's serving point and the service point specified as the overhead conductors?Drop in service. between the service point and the utility's electrical supply infrastructure, the overhead conductors.
The conductors from the service point to the service disconnecting means are what are referred to as by the NEC.Service conductors are the wires that run from the service point to the method of terminating the service (service equipment, not meter). For both above (service drop) and subterranean, service conductors would include service-entrance conductors (service lateral).
To know more about conductors visit:-
https://brainly.com/question/8426444
#SPJ4
Newton's First Law of Motion means that it will take a force to start and stop an object in motion. a) True b) False
To start and stop an item in motion, according to Newton's First Law of Motion, requires a force.
Newton's First Law: What Is It? Why does it mean that?Newton's first law encapsulates the idea that an object's velocity only changes in response to a force. Unless acted upon by a net external force, Newton's first law states that an object at rest will remain at rest and an object in motion will continue to move at a constant speed.
What does Newton's formula's first law state?Unless acted upon by a net external force, Newton's first law states that an object at rest will remain at rest and an object in motion will continue to move at a constant speed.
To know more about Newton's Law of motion visit:-
https://brainly.com/question/29775827
#SPJ4
What is the battery current I_bat when the switch in the figure (Figure 1) is open?
I bat = ___
The battery current is I=9.14A
As per the details share in the above question are as bellow,
The details provided are,
Let us suppose that the current I is flowing through the battery.
The resistor are connected in parallel. i.e
[tex]$3 \Omega$[/tex] and [tex]$5 \Omega$[/tex].
Hence,
[tex]3 \Omega \| 5 \Omega & =\frac{3 \Omega \times 5 \Omega}{3 \Omega+5 \Omega}[/tex]
Further solving it we get,
[tex]& =\frac{15}{8} \Omega[/tex]
The resistor are connected in parallel. i.e
[tex]$3 \Omega$[/tex] and [tex]$1 \Omega$[/tex] .
Hence,
[tex]3 \Omega \| 1 \Omega & =\frac{3 \Omega \times 1 \Omega}{3 \Omega+1 \Omega}[/tex]
Further solving it we get,
[tex]& =\frac{3}{4} \Omega[/tex]
The series sum of the total equivalent resistance is [tex]\frac{15}{8}[/tex]Ωand [tex]$\frac{3}{4} \Omega$[/tex] resistors.
[tex]R_{e q} & =\frac{15}{8} \Omega+\frac{3}{4} \Omega \\[/tex]
Adding the rational number we get,
[tex]& =\frac{15+6}{8}[/tex]
Further solving it we get,
[tex]& =\frac{21}{8} \Omega[/tex]
Identify the battery current value.
[tex]& \mathrm{I}=\frac{V}{R_{e q}}[/tex]
Substitute the value in above equation we get,
[tex]& \mathrm{I}=\frac{24}{\left(\frac{21}{8}\right)}[/tex]
Further solving it we get,
I=9.14A
For such more question on battery current.
https://brainly.com/question/5059264
#SPJ4
Note: The diagram of the question is added bellow,
What factors interact with one another to keep a satellite in orbit. Describe two physics concepts and the effects each has on satellite orbit.
Two physics concepts that interact with one another to keep a satellite in orbit are the gravitational force and the centrifugal force.
The apparent outward force that a rotating mass experiences is known as centrifugal force. Imagine a ball being whirled around on a string or the outward motion you experience when driving around a curve. Since the system is not rotating in an inertial frame, there is no outward acceleration. The ball or your body just continues to go in the same direction that they did at first. However, they seem to be accelerating away in the rotating reference frame of the string or the car. The direction of centrifugal force is always outward and away from the axis because the Earth revolves around a fixed axis. Thus, in the equator and at the poles of the Earth, it is the opposite of the direction of gravity.It is zero at the poles of the Earth.
One of the four fundamental forces of the universe is gravity. A centripetal force is necessary in nonlinear motions like the planetary motion. In the study of disciplines like astronomy, physics, space exploration, cosmology, and many others, both of these forces are crucial.
Learn more about gravitational force here :
brainly.com/question/12528243
#SPJ4
an object with mass m is dropped from rest, one model for its speed v after t seconds, taking air resistance into account, is
The required lim t → ∝ v(t) when an object is dropped from rest is calculated to be mg/c.
Given that,
An object with mass m is dropped from rest and taking air resistance into account.
The velocity as a function of time is,
v(t) = (m g)/c [ 1 - e^-(ct/m)]
v(t) = (m g)/c [ 1 - 1/e^(ct/m)]
lim t → ∝ v(t) = (m g)/c [ 1 - 1/∝]
lim t → ∝ v(t) = (m g)/c ( 1 - 0)
lim t → ∝ v(t) = (m g)/c
Thus, the required lim t → ∝ v(t) when an object is dropped from rest is calculated to be mg/c.
The question is incomplete. The complete question is 'v = mg c (1 − e−ct/m) where g is the acceleration due to gravity and c is a positive constant describing air resistance. (a) Calculate lim t→∞ v.'
To know more about limits:
https://brainly.com/question/12989799
#SPJ4
if Jada has 25 dimes how many quarters dose she have
If Jada has 25 dimes, she has 10 quarters .
What are dime and quarter?Dime is a coin from the United States or Canada which has value of ten cents.
And. quarter is a coin from the United States or Canada which has value of twenty five cents.
Jada has 25 dimes .
Now, we know that 1 dime is equals to 10 cents.
Hence, Jada has = 25 × 10 cents = 250 cents.
Again we know that 1 quarter is worth 25 cents.
So, Jada has = (250 ÷ 25) quarters
= 10 quarters.
Hence, she has 10 quarters.
Learn more about dimes here:
https://brainly.com/question/14534255
#SPJ1